Version 1.5
3.5 Leuchtmittel-SteuerungBeim VS P3 stehen folgende Möglichkeiten zur Leuchtmittel-Steuerung zur Verfügung:Einstellungen zur werden in der Personali
4. KanalbelegungAufteilung der einzelnen KanäleJB MODEHOG MODEKanal 1 Pan 430°Kanal 2 Tilt 270°Kanal 3 Pan feinKanal 4 Tilt feinKanal 1
Iris zuIris fade zu (schnell 0,6sec-langsam 4,8sec)Iris aufIris fade auf (schnell 0,6sec-langsam 4,8sec)Iris zuIris Zufal
000-003004-007008-011012-015016-019020-023024-027028-031032-035036-039040-043044-047048-051052-055056-059060-063064-191192-222223-224225-255000-015016
5. Service5.1 Gobos wechselnDie Gobos sind mit einer Feder in das Gobozahnrad gespannt. Zum Wechseln lösenSie diese und befestigen Sie dann das neue G
5.5 Drehbare Gobos ölen5.4 Optik reinigen5.3 Gerät reinigen5.2 Leuchmittel wechselnSiehe Kapitel 2.2Sie sollten in regelmäßigen Abständen die Funktion
5.7 StromlaufplanDrossel 150Hz60HzPhDLANZünderLüfterKondensatorTrafoHead 3Head 3Head 4Head 1Head 1Head 2+15VGND+32V+5Vgreygreenyellowbrownbluegreenyel
Konformitätserklärungim Sinne der Richtlinie 89/336/EWG(Richtlinie 89/336/EWG des Rates vom 03.05.1989 zur Angleichung der Rechtsvorschriftender Mitgl
English19
1.3 Technical dataweight:21kgPower connection:230 V 50 HzPower consumtion: 2,1 Alight source: OSRAMBaby-SharXSHTI250Wmax.ambient temp
Inhaltsverzeichnis1.Einleitung...2. Installation...
Insert the lamp into the lamp holder. The nipple of the lampmust face the top lid of the head. (See sketch).If changing the lamp, remove old lamp from
2.3 Rigging the fixtureThe Varyscan P3 can either be placed on the floor or hang on a trussing system in avertical or horizontal way.If mounting the
3. Control panel2.5 Installing a plug on the power cordInstall a plug like described in chapter 2.2.Connected load: Voltage 230 Volts, frequence 50
3.1 Menu navigationSERVICEDMX-TESTINFODMX CHANNELSOFTWARE VERSIONFIRMWARE VERSIONREM. LAMP TIMELAMP STRIKESTOT LAMP TIMETEMP BASETEMP HEAD PCB.RESET ?
3.2 Set to factory default3.4 Standalone mode3.3 DMX AddressingEnter DMX address by means of the keys "+" and "-". Confirm an stor
Reset DMX values of a step:To reset the DMX values of a step proceed as follows:Press key "Menu" one time. Then press 5 times key "+&qu
3.5 Lamp control and lamp ignitionThere are differnt modes for lamp ignition and lamp control available:Lamp ignition configuration is set in the fixt
4. DMX ProtocolChannel allocationJB MODEHOG MODEChannel 1 pan 430°Channel 2 tilt 270°Channel 3 pan feinChannel 4 tilt feinChannel 1 pan
Iris closediris fade closed (fast 0,6sec-slow 4,8sec)iris openiris fade open (fast 0,6sec-slow 4,8sec)iris closediris rand
000-003004-007008-011012-015016-019020-023024-027028-031032-035036-039040-043044-047048-051052-055056-059060-063064-191192-222223-224225-255000-015016
1. Einleitung1.1 AllgemeinesDer Varyscan P3 250HTI verfügt über 7 Farben plus weiß, ein Farbeffektrad mit Frost-filter, CTO- und CTB-Filter,pink, cyan
5. Service5.1 Gobo changeThe gobos are fixed by means of a spring. To change gobo remove spring andgobo and insert the new gobo. Readjust the spring t
5.3 Cleaning the fixture5.2 Lamp replacementsee chapter 2.1To ensure a long and satisfying performance of the fixture, check function of theVS P3 fans
5.7 Wiring diagramBallast 150Hz60HzPhDLANIgnitorFanCapacitorTransformerHead 3Head 3Head 4Head 1Head 1Head 2+15VGND+32V+5Vgreygreenyellowbrownbluegreen
Declaration of ConformityIn terms of directive 89/336/EWG(Directive 89/336/EWG of the council from 3 May 1989 for approximation of agreedRegulations o
2. Installation2.2 Netzstecker montierenDie Montage des Schutzkontaktsteckers, bzw. der Anschluss des Varyscans an dieStromversorgung (230 Volt, 50 He
2.3 Montage der GeräteDer Varyscan P3 kann auf den Boden gestellt, oder an den dafür vorgesehenenCamloclaschen senkrecht oder waagerecht montiert werd
2.5 Netzstrom verkabelnAm Bedienfeld im Fuß des Gerätes können sämtliche Parameter des Varyscan P3eingestellt werden (siehe Menü-Übersicht nächste Sei
3.1 Menü-ÜbersichtSERVICEDMX-TESTINFODMX CHANNELSOFTWARE VERSIONFIRMWARE VERSIONREM. LAMP TIMELAMP STRIKESTOT LAMP TIMETEMP BASETEMP HEAD PCB.RESET ?+
3.2 Parameter zurücksetzen3.4 Standalone-Betrieb3.3 DMX AdressierungDurch drücken der Taste "+" oder "-" kann die DMX-Adresse verä
Zurücksetzen der DMX-Werte in einem Schritt:Sollten Sie die DMX-Werte eines Schrittes zurücksetzen wollen, dann gehen Siefolgendermaßen vor:1. Drücken
Comments to this Manuals